2nd Look: Rottefella NTN Freedom Binding

Downhill Performance

Overall, the NTN Freedom is a solid option for descending. I prefer a telemark binding that quickly creates high levels of spring tension when I lift my heel, which some refer to as a more “active” binding. I have known telemarkers who prefer less active bindings, but there seems to be an overall trend toward bindings that are more powerful in this sense. For me, the benefit is the ability to push harder on the ski tip while maintaining a more athletic and powerful, upright stance.

Paul Forward, NTN Freedom, Blister Gear Review
Paul Forward on the NTN Freedom, Turnagain Pass, Alaska. (photo by Charlie Renfro)

Spring Stiffness Levels

Both of the current NTN bindings have a large range of adjustment in this sense. The Freeride has a choice of three different spring stiffness levels: Green (relatively soft), Blue (medium), and Red (quite stiff).

The Freedom uses interchangeable “power boxes” and comes in Green (soft) and Blue (medium). I have only used the blue power boxes and, as noted above, prefer the stiffer settings. I would estimate that the blue springs on high settings are about 10-15% less active than the red springs with similar 5/5 settings, but that’s just a guess.

For the sake of comparison, I’d say that that the stiffest NTN Freeride / Crispi Evo combo with Red springs on 5/5 is similar to a TwentyTwo Designs Axl / SCARPA T-Race combo somewhere between the 2nd and 3rd pivot position with the “Stiffy” spring kit. The flex is different in its progression, but comparable. The Freedom / Evo on high settings with blue springs is around the same as an Axl with normal springs on the 3rd pivot.

Spring Tension

One aspect of the Freeride that has always been less than ideal for me has been the relative lag in the onset of spring tension when raising the heel. It usually requires the boot to be at least one to two inches off the ski to start activating the springs. This is caused partly by the sole rocker of the boots after skiing on them for a few weeks, and creates some play in the system that can be unsettling during technical skiing.

The Freedom improves upon this with more of an upramping toe piece, and gives more immediate power to the ski, even with my older, well-used boots. To me, this is enough of an improvement to make me favor the Freedom in all but the heaviest crud, where the Freeride’s extra spring power still helps. The best bindings I’ve used for immediate power transfer are the Axl and the Hammerhead, and both are a little better than the Freedom.

In terms of lateral stiffness and stability, no tele setup I’ve used is better than either NTN binding paired with the Crispi Evo. T-Race’s with Bomber Bishops are close, but the NTN/Evo combo will drive fat skis on hard snow better than any telemark gear out there. It also creates a fun, stable platform for anything from powder skiing glades in Japan to smashing through crud at Alyeska.

Releasability

I have released from the NTN Freedom once during a fall while skiing at high speeds in choppy snow at Alyeska. I don’t know if the binding saved me from injury, but it seemed to function appropriately. And I have not had any prereleases.

Other Issues

Kate pointed out that one of the great features of the NTN Freeride is the swappable plate system. If a skier owns several pairs of skis, it is possible to purchase and mount simple metal plates to quickly and easily swap bindings from one pair to another. This Freeride plate also allows for three different positions spaced about 1.5cm apart to adjust the binding position without re-drilling. Probably in the interest of weight savings, the Freedom goes to a direct 6-screw mount. For those curious, it is possible to mount skis with Freedoms that were previously drilled for Freeride plates without having to move the binding position too drastically.

Durability

So far the Freedom has held up well without any signs for damage. For reference, I broke the aluminum frame on three different pairs of NTN Freerides in as many years, so I think the Freedom is a reasonably tough binding. But it is a more complicated binding with a lot more moving parts than a traditional cable binding, and might be harder to repair in the field.

NTN Freedom vs. TwentyTwo Designs Axl

I’ve touched on this above, but I feel like the TwentyTwo Designs Axl is the most apt comparison for a powerful tele binding that still tours well. The NTN Freedom setup is substantially lighter, but the touring mode on the Axl has better ROM and less friction. Both ski very well, albeit differently, with the NTN being more laterally stiff while the Axl has a smoother and more immediate forward flex. Like all things telemark gear, this will come down to personal preference and boot choice. In my opinion, both bindings are as good at it gets for telemark in 2013, though I have yet to try the new G3 bindings or the Telemark Tech System….

Bottom Line

The NTN Freedom is a great binding that tours well and is fun on the descent. Telemark gear has generally seemed to lag behind AT gear, but the Freedom is making steps in the right direction, with an emphasis on being light, powerful and reliable.

33 comments on “2nd Look: Rottefella NTN Freedom Binding”

    • Hi Bill, Thanks for reading! As far as I know the Freedom will be unchanged for this season. The Freeride got a new color scheme but also appears mechanically unchanged from last years version.

  1. Hello Paul,

    I am looking for a NTN binding for my new touring ski. I actually ride the NTN freeride and this binding is awesome. So I started to read about the freedom, the lightest version of the freeride. I found some reliable issue from some customers like; short elevators kept on collapsing, consistently the bindings pops up into touring mode when descending and the lever pops out of position when fastening the binding a bit too easily.

    So should I stay with the freeride, witch seems more reliable, or the freedom might do the job as well.

    Thanks again for all your great review.

    Simon

  2. Thanks Paul (and Kate) for the reviews.

    It is great skiing the NTN and commiting to them after almost 30 years on all the other 75mm free heel bindings. I need to sort out extra base plates, for extra skis. I’ve already got 2 pairs of NTN, one with a metal plate and the newer (2012?) Freeride, the one with the pink plastic plate. And now, of course, we also have the still more sexy Freedom (lets not confuse those model names..!). Can you add a little piece on NTN evolution and compatibility? I watched when the NTN first came out (red ones) years and years ago at this point (2006?). But I waited until about last year to convert. Cheers, Geo

  3. Thanks for the review.

    Do you know of any NTN boots that would be a bit more relaxed, more of an all-day touring boot?

    I’ve got Prophets and like them, but I would love a lighter weight, more comfortable boot for all day stuff, even though it means losing strength.

    Hear of anything?
    Thank you!

  4. Nice review, but you guys should all switch to a telemark tech (tts) binding. The weight is nothing! Combine a dynafit tow (you can buy them online from a split board company) and take a old G3 wire and then buy the conversion kit from Wasatch Ski Distribution. The system totally works and it is very powerful. And of course the super light weight makes it a dream for touring. The telemark companies have really lost their way on that one – not sure why BD and G3 don’t make a version but surely it is coming. Enjoy the turns!

    • Hi Mike K,

      I tried telemark this year first time a couple of times, and I will like to buy the right equipment. As I used to use touring ski and boots, do you think it is even possible to use a common ski mountaineering boots like mine tlt5 with the telemark tech (tts) binding?

    • more weight = better workout = better fitness,strength and health.
      less weight =s easier = less workout = softer body
      unless you are counting micro seconds in an Olympic medal competition, man up and stop counting ounces. Unless you are the least fit of your group, you need more weight to keep yourself challenged and not bored.
      If you’ve come to Tele, you must already know that harder is always better than easier, in every aspect of life!

      • If you want it to challenged go higher and further, don’t go heavier. Training at home is a workout, climbing a mountain is an adventure.

  5. The TTS isn’t smooth as the Freedom on the downhill. I have both, and really don’t like the TTS feeling.

    Why don’t you actually weight the binding when you do such a long review ? The weight of the whole binding is not what is advertised by Rotte…

  6. Francesco, you still need a boot with bellows above the toe so it can flex to allow you to stay on the ball of your foot. Scarpa makes the TX pro boot with tech fittings. That’s the one I use. I’m not sure about the other manufacturers.

    Jeff D, TTS is very dependent on the spring setup that you have. It does engage earlier so I “borrowed” the silver G3 cartridges from a buddy and then put the heel riser in the loosest position that it still engages. It makes the whole system more like a traditional 75mm binding. In the end the weight savings are so huge that I can’t use the NTN bindings for touring. For on piste sking and ripping whistler Blackcomb to shreds, then fo’ shizzle the Freeride kicks ass. But it’s hard to keep up with all my buddies on dynafit set ups and Peter Pan feather weight boots. At least TTS gives us the binding component. Tele boots still remain crazy heavy in comparison to AT but we suffer for having extra soul in our turns :)

  7. Mike K, I have tested the TTS with Scarpa Tx (orange, very soft version) and both switchback and switchback X2 springs, various pivot points, even Scarpa F1… I can’t find a setting that has enough tele spring engagement and a smooth flex. Whereas the NTN Freedom is very smooth out of the box, and a real bliss on the down. I think the TTS needs longer and softer springs.
    For long alpine touring, I’ve switched to 100% tech bindings until a very light tele binding that I like is released.

  8. Just completed 6 days touring in the Pyrenees and the real problem with these bindings is that you can’t fit ski crampons which are really essential on steep icy slopes. I’ve used them now for over a year and they have never released which is a bit unnerving. I think I’ll be switching to Dynafits before I do anymore serious tours.

  9. John, just switch to TTS. If you use the dynafit toe it takes crampons. It has release on me when i have needed it. and of course as you know with dynafit, you can lock and unlock the toe as you wish. SO if you are doing a soft bowl, but are worried about it sliding, then leave the toes unlocked. it won’t release in powder unless you hit a rock or death cookie. But if you are doing a gnarly couloir, you can lock in. I usually keep it semi-locked in the first click. and it has release if i bail hard.

    I have now used TTS in the BC and in Niseko/Furano Japan for a full season. Both on piste and backcountry. It is awesome. so in credibly light and lots of power. I find it has smooth flex and it never hinders my skiing. it is frankly awesome! I still can’t believe no big company is jumping on board with this. Not sure why

  10. Thanks Mike, just to be clear I was referring to NTN bindings. I’ll check out the TTS then if it can take the Dynafit toe. To be fair to NTN I do find them a lot more stable than my old 75 mm and no problems with getting in and out in deep snow. Getting in on a gradient however is tricky. The real disadvantage of the NTN is inability to take a ski crampon. Lack of release even though I’m using the correct spring setting is worrying. I’ll be seeking advise on this from Rotefella. I’m using Scarpa Terminator boots which I love and are Dynafit compatible.

  11. Thanks for the great review. As is understandable, much of your review and most others discuss the advantages of the Freedom over the Freeride for touring and going uphill. For several reasons (time, alpine skiing friends, wife concern about avalanches), my telemarking is done 100% at lift serviced resorts.

    So the question is if you were only going downhill on them in resort conditions – powder when available but otherwise crud, bumps, glades, chutes – and mounting them on regular alpine skis (likely the Blizzard Bushwacker or Bonafide), would you go Freedom or Freeride? Rotafella seems to push the Freeride for that purpose, but you comments about increased range of motion, equivalent edge hold, and perhaps increased reliability indicate that you might think Freedom is better. Swappabity across skis is not that important because you can do that with either binding using quiverkillers.

    Would love to hear your thoughts on this.

    Thanks!

  12. For resort use only, I would definitely use NTN Freeride. There’s more torsional stiffness and available spring retention than the Freedom that make them more suited to drive big skis on icy slopes and hard snow. With the Freedom on blue #4 (one notch more than the average setting for my weight/boot size), I can’t get the same power from the binding to the ski.

    The Freedom might be easier at first, or have a more “traditional” feeling for telemarkers coming from a 75mm setup, but that’s it.

    BTW, you can get ski crampons for the Freedom at B&D ski gear.

  13. As someone who has skied and toured Rottefella Freedom and Axl during the last southern hemisphere season (NZ), plus neutral and laterally rigid bindings in earlier seasons (Linken, Voile VPII), I just want to reinforce for other readers that your review is an accurate assessment in my opinion.

  14. Hey Paul,
    How did you like those orange crispi evos? Im a an ex apline racer getting some ntn gear together and already have a pair of freedoms mounted on some BD megawatts. Found a great deal on those same evos you wore for the review but have heard lots of complaints about stiffness. Any insights? Im 6′ and close to 200lbs, aggressive skier, so im thnking a used pair might not be too stiff for me. Cheers!

    • Hey Tanner, Thanks for the message. Yes, I think you’ll like the orange Crispi Evo’s. I’ve had 2 pairs of them and I think that a skier our size should have no trouble flexing the bellows. I think you’ll dig the extra power. Good luck and let us know how it works out for you.

  15. I have to disagree completely with the assessment that these are durable. They are not even ready for prime time yet, and should be considered a beta release. I have had them break on my twice in less than 20 days. I’m 6’3″ 220 and a super aggressive skier, but I only had my old voile hardwires break on me 3 times in a decade of skiing on them. The first breakage, a plastic piece under the tow broke and fell out while skiing bumps at breck, and I was unable to get my boot out of the binding, having to walk back to my car in my sock. After the super crappy customer service, I finally got a replacement binding from Rotte after 1 month, and skied them 5 days and the binding broke into about 12 pieces while skiing down the highlands bowl. Also, the lever for switching from tour mode is super unreliable and pops into tour mode quite frequently. Finally, they have designed this binding with so many nooks and crannies that the binding is prone to icing up all over the place, not least of which is the tour mode lever. When they work, I agree, they are a great backcountry setup. But think twice about trusting them deep in the backcountry.

    • Hei Drew

      I had the same problems as you. I used them in spring for easy skitouring and they were OK. But next fall, when I used them on hard slopes, already the first day of skiing, I broke the plastic piece that stops the bindings touring mode. I had them replaced quickly, but I broke them just two skidays later again. This binding might be OK for lightweight touring, but not for skiing aggresively. In the end, they just ruined my skis since I had to drill them twice.

      Best,
      Philip

  16. Since my last comment, in Sept 2014, I had a slow crash with the Freedoms, they didn’t release, and I broke my ankle. Click my link to read the full story.

    The B&D crampons work very well with the Freedom, with one important caveat. While striding, depending on factors such as length of boot, position of crampon hinge, etc, you might find that the rear of the crampon nicks the spring adjustment knobs, every stride you take. This happened to me, and eventually, far from civilisation, the knob was leveraged off like a bottle-top, and all spring tension lost. By a miracle I found the knob back in the ski track and it popped right back on. The solution is to grind a piece out of the crampon so it doesn’t catch.

    To bench-check for fouling between crampon and binding, you must have the boot clamped in the binding in tour mode.

  17. I had the steel bail/like piece on the freedoms come out on some easy lift served skiing.Seems like it could have a circlip or cotter clip holding it on.But it stays in if you bend it out slightly and squeeze it back into place.Seems hoky though

  18. Hi.
    The Scarpa TX is my first plastic boot and Im totally impressed. Is it possible to just lift the release mechanisme while we are falling? Sounds like a fair stunt?

    Got the Freeride binding (2148g) and Stormrider DP Pro 184 ski (4100g). I enjoy the high speed stability from the weight!

  19. Hey folks. I am new to Blister, so greetings everyone. Question regarding NTN Freedom. Does anyone experience a slight resistance in tour mode. I feel it on the bench cycling the binding in tour mode with boot installed by hand. Not so noticeable when actually touring. However , if I feel it while bench testing, the resistance is there. Just curious if I might have an adjustment issue or whether it is normal. I am using blue cartridges’.

    I am gravitating back to the Freedom due to continued frustration with my 22 designs Outlaw set up relative to the finicky step in action of that binding. Was working just about decent without brake installed and was trying to really be optimistic and like it ( brake is an absolutely terrible design and should not be offered until it is refined more, IMO ) , however, I have had it . Not fun when transitioning after a long tour / climb!!Really not at all. So , before I return to 75MM as my primary set up ( Oh how I miss the simplicity and functionality of my Voile Switchbacks ) wanted to give the Freedom another go.

    Thanks for any insights

  20. Hi TA1, yes the slight resistance in touring mode is normal. Presumably this does soak up a little striding energy, but I don’t think anyone has ever complained that they have noticed it in practice. I certainly haven’t.

    I’ve gone the opposite way to you and gone to Outlaw, to get the classic 22 Designs heel retention power, which I enjoyed with the Axls. I don’t have the brakes. Due to going to AT bindings the last couple of years, I haven’t used the Outlaws enough to offer feedback.

  21. Thanks for the insight Peter. Yeah, after a more thorough reading of an Earn Your Turns and the Blister review on the Freedom , the reviewers do touch on the resistance that still exists with the Rottefella design. Not a big issue for me, just wanted to be confident that it was not a defect in my bindings or poor adjustment, etc. Regarding the Outlaw, I really like how it skis. I just find it overly awkward to get into and out of the binding. Also, for my tastes, I find it a bit heavy and clunky to tour with as compared to my Voile Switchbacks or a tech toe AT set up / Dynafits . The Freedom lags behind a Switchback binding or a Dynafits set up for touring in my opinion as well. Although I have both an Outlaw and Freedom option, for long days of touring and backcountry skiing, my Voile Switchback set up is still my go to rig. I’ll grab the Outlaw or Freedom set ups for resort / lift served side country days where I don’t have to worry about any uphill/skins transitions ,etc. . Anyway, hopefully 22 and RF continue to refine their designs. Always great to see innovation in the Tele segment.

    Tony

  22. This thread is amazing! Wealth of experiences; really useful. Just done a short tour on Freedoms, in appalling British (!!!) conditions. Serious freezing issues between tour and Tele mode, and in general. Had the same issues in Verbier. Both times had to take the skis off to hack free (family had to cut me out off the ice in Verbier). Not fun in blizzard conditions. Potential solution is the old one of pre-spaying with WD 40 or similar. Am going to try the new French Meidjo, but suspect that all bindings will freeze up to some extent; depending on conditions.
    BD kicker (short) skins worked well, but I take tape just in case (and a suitable ice hacking screw driver- not knife).

  23. just checking in again after 5 years, and invention of the 22 Designs Outlaw & Meidjo (neither of which I have ANY experience with, although we would of dreamed such dreams in the 80s & 90s…).

    I have been skiing NTN Freerides and Freedoms with zero problems for at least 5 years. Love ’em. Not doing much BC (actually some on both of these “heavier” rigs), or simply using my 75 mm set ups).

    I just want to say that I ski the Freedoms on lift service because they seem just as bomber, yet lighter.

    Have fun. Ciao

  24. Bought the Medijo, weight a revelation, put them on an excellent pair of touring Movement Skis.

    Exceptionally light set up and little tour resistance.

    No ice build up of note.

    Downhill performance is excellent on the Meidjo; you can get old style low ( I like that old school low)

    3 BUTS;-

    1) Needs fiddling to find right tele spring tension, or even put in the extra stiff springs in supplied with them (I did not as I am light, small and weak). Do this fiddling before a bigger trip.

    2) Bindings are awkward to get into, especially off-piste in deep snow, more than once I ended up chopping a mini platform and blowing like stink to get snow off binding, to get the pin techs in- all the more awkward with ski brakes. However, its the same problem with any pin binding, or any binding in reality. Think I’ll stick with the brakes as I don’t like the idea of leashes (even avalanche rated) in an avalanche, as they are so variable and sometimes unpredictable.

    3) Slightly worried with robustness of the parts? However I have not had, or come across breakages; guess they must be pretty robust as a friend of mine ripped his M2 out of the skis (not the fault of the binding!).

    Lately I have been skiing them in preference to my Freedom- I have done this automatically, without thinking about it; actions speak louder than words?

    Looking forward to trying the 22 designs Lynx.

    Tele is alive and well!

    Oh what fun! Off to Austria now (with both Meidjo 2 and Rottefella).

    Be safe, and cool.

Leave a Comment