The most honest and in-depth reviews of outdoor sports equipment on the planet.

Outerwear 101

Outerwear 101, Blister Gear Review[Editor’s Note: We posted this article by Sam Shaheen last fall, and if you missed it back then, you don’t want to miss it now.]

 

There is a ridiculous number of outerwear choices these days for skiers and riders, and jackets range from $60 to $1000 on up. This article aims to help you figure out what you need, what you don’t, what all of these waterproof / breathable ratings mean, and what you’re actually going to get out of that sick neon green jacket you’ve been eyeing for months.

But the truth is, this isn’t really a 101 article. We’ll discuss the 101 basics, but we’re going to jump down the rabbit hole a little bit and discuss various waterproof membranes, the BS that is breathability ratings, GORE-TEX vs. eVent, 2-layer vs. 3-layer construction, Polytetrafluoroethylene, and a little bit of applied chemistry.

Origins

As far back as 190,000 years ago, people were draping themselves in animal skins in order to survive the cold. They developed technologies such as the needle and thread (made from bone and natural fibers), and used these to sew their pelts into more flattering patterns.

This rudimentary outerwear production continued for thousands of years, with the first fuzzy evidence of knit or woven textiles showing up only around 6,000 B.C. At this point in time, primitive garments could hardly be considered “outerwear” and were used mostly for decorative purposes.

So the real history of outerwear begins with the Vikings. These guys were burly. They lived in the cold, had huge beards, and spoke a language that sounded like an MMA fight. Hence, you might not expect that these tough guys were actually designers. They were the first to begin wool production, dying, and pattern making, all in a rather desperate attempt to stay warm.

A shaggy, homespun viking cloak

A homespun Viking cloak. (aka, paleo-Arc’teryx?)

For the next thousand years, wool and skins ruled the outerwear world.  Even up through WWII, wool and leather were go-to fabrics.

What these thousand years lacked in textile technology they made up for in advances in sewing and pattern making. Fully lined garments were the norm, with complicated patterns that incorporated multiple types of stiches. Technology such as zippers (all metal), snaps, and buttons were used extensively.

Then, in 1955, Velcro was patented, and the nylon textile industry took off.

History of Gore-Tex and How it all Works

The next advance in the history of modern outerwear was a little invention patented under the name “GORE-TEX.”

By the ’60s, nylon fabrics with polyurethane (PU) coatings that were completely waterproof were available. However, these new fabrics lacked any sort of breathability, which made them terrible to use in active wear garments. Enter Bob Gore.

Working with his parents’ company, W.L. Gore & Associates Inc., Bob Gore began experimenting with polytetrafluoroethylene (PTFE), a polymer of carbon and fluorine (in technical speak, four fluorine molecules per each ethylene- in a polymer). Nowadays, it is better known under it’s DuPont brand name, Teflon™.

Bob Gore, Blister Gear Review

(Revolutionary AND steezy!)

More specifically, Gore was researching expanded PTFE (ePTFE) for use in plumbing as thread tape and sealant. It turns out that ePTFE stretches quite well, and forms a stable, though delicate, web-like structure upon expansion, filled with millions of tiny pores. The “stretchiness” of the ePTFE is what made it commercially viable as a joint sealant. In 1971, the first GORE-TEX products hit the market, sealing threads and joints all across the country.

33 Comments

  1. Mr. P November 19, 2011 Reply

    Amazing article. Thanks so much. So enlightening.

    Keep bringing it!

    P

  2. rangerjake November 29, 2011 Reply

    Freaking killer articles. All of them. Even as a seasoned gear shop employee and tech junkie, can always count on Blister to deliver the goods on beta, science, and the layman’s terms to tell the whole story.

    Keep up the really really ridiculously awesome work.

    jake

  3. Sam Shaheen November 29, 2011 Reply

    Thanks for the kind words fellas!

  4. abbie November 29, 2011 Reply

    genius. i’ll never look at gore-tex the same way again. nice work man.

  5. Brian November 29, 2011 Reply

    Such an interesting perspective on technical outwear, and an entertaining read!

    Thanks for the great article!

  6. auvgeek December 26, 2011 Reply

    Amazing article. Can’t believe I missed this when it came out. Blister FTW.

  7. Bert January 2, 2012 Reply

    Wow. Technical yet totally accessible article. Great, great read for anyone looking to buy waterproof, breathable gear. I learned a lot & will try to spread the word about this article. Thanks!

  8. Leigh September 25, 2012 Reply

    Really in depth article, but really useful even for the non technical out there. You covered some great points. Time to go shopping for the right balance of tech in my new jacket! I’ve shared this on our Facebook, will be really useful to our followers.

  9. Andrew September 25, 2012 Reply

    Finally, an article that doesn’t reduce a complex issue to a couple of bullet points. Thanks!

  10. Blister Member
    Mark October 30, 2012 Reply

    Terrific article! Might I suggest for Outerwear 102 and article about actually dressing for skiing/boarding? How are the various layers supposed to be used? What do you guys wear for different conditions? Two layers? Three layers? How should you layer under a shell? Think would be a useful companion. Keep up the great work!

  11. Dan December 15, 2013 Reply

    Great Article!
    Was just about to buy 3L Gore pants… Questioned my choice (and the price)… Found your article… Read the whole thing… And just ordered the pants!
    It confirmed my decision — also answered my long wonder about how the 20k/20g (etc) ratings compared to others and if they really could be trusted. Answer = no more board shop employees trying to sell me over priced claimed “technical” wear.
    Thanks!

    • Sam Shaheen December 16, 2013 Reply

      Hey Dan, glad I could help out!

  12. mcfarljc December 21, 2013 Reply

    This is a fantastic article. Where does Dermizax fall? I keep seeing the material in very high end Kjus ski jackets; is it simply a PU laminate? If so, I can’t imagine the performance would warrant the $1500 price. They claim incredibly high breath ability scores, but thanks to your article I now know to ignore them :) There also appears to be several versions of Dermizax. Is this material any good?

  13. John February 8, 2014 Reply

    Most helpful article. Thank you Sam for the time and effort you invested to write this!

  14. Blister Member
    Slim October 4, 2014 Reply

    Great article, nice to see one of these that doesn’t spew the misinformation of water drop vs vapor molecules through holes stuff.
    The one thing you didn’t stress was the effect of shell and liner fabrics on breathability of the total laminate.

    • Sam Shaheen January 12, 2015 Reply

      Hey Slim,

      That is definitely a huge part in the total breathability of any garment. A bit difficult to baseline, but certainly a huge factor. Thanks for your comment!

      -Sam

  15. just me November 7, 2014 Reply

    stupendous and layman friendly article! it took me a few minutes to fully absorb (he he) all this ‘dry as a bone’ information to great effect. no ‘watered down’ or fishy patent references to get wallowed down in either! wish there were more ‘commercial’ PR folks who had the smarts to actually divulge facts, rather than foist their marketing jargon upon so many naive buyers!

  16. alvin January 5, 2015 Reply

    So far what I’ve read on this site has been very useful, and I like the writing style. I don’t think I’m the only one around that is sick and tired of being treated as an imbicile, or worse, just a source of income by sometimes dishonest outdoor companies that are run by the marketing departments. Even companies like Patagonia, TNF, and others that started off right, by climbers and such, have gone far astray, letting the marketing departments and “the bottom line” affect their decisions.

    Hell, Gore’s lies have killed people, hypothermic in their own sweat. How the f__k is that “keeping you dry”? Meanwhile they have made billions.

    Good to see a honest, independent source of information. I hope you continue.

    Got anything on Pertex Equilibrium, by chance?

    • Sam Shaheen January 12, 2015 Reply

      Hey Alvin,

      Pertex Equilibirum is a non-laminated (no membrane) fabric that acts like a very thin softshell. It is typically used in very lightweight garments and is not waterproof.

      Like most non-laminate softshells, Equilibrium claims “weatherproof”-ness by using a high density weave on fabric exposed to the elements.

      What makes Equilibrium a higher performance fabric than some others in this category, is the use of a denier gradient to facilitate breathability by capillary action throughout the fabric.

      Basically, the inner layer of the fabric (against skin) is woven with a larger diameter fiber than the outside layer. This creates a driving force for capillary action out of the garment for breathability.

      I hope that answers your question,
      Sam

      • alvin January 12, 2015 Reply

        Yes, that is very useful information. Thanks a lot.

  17. alvin January 5, 2015 Reply

    Is it just me, or is DWR way, vastly, overrated? I’ve had any number of pieces with DWR. Typically they stop working within minutes of a light rain, even when new. Of course it gets worse after even just a couple washings. And I buy good quality (in every other way) expensive stuff (Patagonia usually, also Arcteryx, Lowe Alpine, others)…I’ve yet to see DWR work properly. Ever.

    • Sam Shaheen January 12, 2015 Reply

      DWR is a tricky thing to nail down. The performance depends on many things. When you have Patagonia claiming to put the same DWR on their M10 3L hardshell as a pair of casual pants, there is obviously going to be some performance differences.

      In many ways, the fabric that the DWR is on is just as important as the DWR itself. Low density weaves, stretchy and high denier fabrics (like a lot of casual clothing) typically don’t have the same DWR performance as high density weaves on laminated fabrics.

      Bottom line: DWR is essential to your hardshell, not so much to your “softshell” crag pants – and even then, performance varies wildly.

      • alvin January 12, 2015 Reply

        thanks, that makes a lot of sense. Even still, I haven’t had much luck with DWR on anything at all, honestly. My hardshell always wets out on the surface, and then doesn’t breathe, or even in cold weather sometimes becomes a sheet of ice-fabric.

        It’s funny but just today I recieved email from a well-known, highly experienced outdoorsman who I happened to ask some of these questions to, and he told me he often uses an umbrella!

        Others suggest those cheap plastic ponchos. That says a lot about the state of these “high tech” (and ridiculously over-priced) garments, I think. You can buy a lot of umbrellas and ponchos (or Hefty Bags!) for 600 bucks, eh?

        • Sam Shaheen January 12, 2015 Reply

          You know, that is a great point to bring up. Depending on what you’re doing outside, often an umbrella or poncho is all you really need. Hardshells do NOT excel in rain, they just don’t work well for many reasons. If you’re in the rain and don’t need both hands, or aren’t sweating extensively, there are other options.

          The reality of the situation is that 90% of the time you’re outside, you don’t need anything more than wind protection. In heavy, wet snows and rain — the other 10% — you need the protection of a hardshell. But most people (including me) go out in a hardshell almost everyday… Something I’ve been pondering a lot lately. Can a non-hardshell based layering system catch on in mainstream snow sports?

          • alvin January 12, 2015 Reply

            I had heard they already are popular in skiing and snowboarding, when the lodge is right there. I don’t believe a hard shell is all that necessary in snow for a few reasons: 1. snow takes time to melt, and brushes off easily, 2. snow is 90% air anyways, 3. in the cold, humidity is lower (i find things dry quite fast in the winter, IF they ever get wet in the first place, that is) 4. you don’t sweat as much in the cold, leaving the insulating and wicking layers with only external moisture to deal with 5. i had another one but forgot it right now kk

            It seems to me, from experience of myself and others, and just logic, that the only truly difficult conditions to deal with (from a clothing perspective anyways) are sustained, cold rainy conditions, with temps above freezing up to the low 50s or so. And only then, really, when you stop hiking. As long as you are moving, you are generating plenty of warmth, and continuing the evaporative process. As soon as you stop either the rain that soaked in, or the sweat under a hard shell immediately makes you start chilling, and fast.

            That’s my opinion, and I am going to start testing some soft shell combos when i get the chance in those kind of conditions. Honestly, how often do you get those kind of conditions? Not much, thankfully. But I plan to seek them out as soon as my new Equilibrium shell gets here! ;)

          • alvin January 12, 2015 Reply

            There is one garment that works well in chilly, wet conditions…the old school wool sweater, the think, airy kind (knitted i guess)…those things keep you comfortable in all kinds of conditions, and don’t over-heat readily. I’m sure the Llama ones in the Andes and the Yak ones in the Himilaya must just be superb, since those places are cold and people live up to 6000m above sea level.

            Someone should really start researching this more and try to produce things of this nature commercially. I’m not sure what Sir Edmond wore, but I bet there was wool, maybe even Yak wool, involved…and clearly his porters were using that. Heck, they didn’t even have polyester in those days, I don’t think! :-D

            • alvin January 12, 2015 Reply

              Yes, if anyone knows of someone making Yak-wool sweaters, let me know. Maybe it could then be lined with micro-fiber and shelled with Pertex too…oh that would be great….heavy as hell, but great.

  18. Rosanna January 11, 2015 Reply

    Brilliant article. It means even for an accomplished tailor/seamstress diy’ing a good shell that functions properly will take some thought and care. Tips on what to look for in terms of construction of a commercial garment would be great.
    Many thanks!

    • Sam Shaheen January 12, 2015 Reply

      Hey Rosanna,

      I assume you’re looking for a commercial garment for inspiration in making your own? My advice would be that quality is less of an issue than simplicity.

      If you’re making a 3L shell, precise patterning is essential, so much so that most major companies laser cut their fabric. The margin for error is tiny.

      If you’re making a 2L shell, again, keep it simple! These garments can get extremely complicated!

      Let me know if you have any other questions! I have commercially produced both 2 and 3L shells and may be able to answer your questions.

      -Sam

  19. Kevin January 10, 2016 Reply

    Great article, one of the best i have ever come across. i just wanted to add a nit-sized comment – i have a Patagonia 2.5 layer ski jacket with the “H2No” membrane, and just a mesh liner that is not laminated to the membrane, but just hangs loose in the garment – I thought that was what was meant by the half-layer, but i see it’s used to describe a variety of materials and construction that is more than 2L but not quite a 3 layer build, either. so… Veritatem dies aperit… thanks again for the very informative article!
    -Kevin

  20. Blister Member
    Greg February 14, 2016 Reply

    Fascinating! Thanks for the article. It’s so refreshing to have someone putting solid content out there. Most big publications could learn a lot from what you do. I’ve come to realize that soft shell jackets and pants with the right layer(s) underneath and a good or refreshed DWR finish are the most comfortable in all but the worst weather. Some trips are too remote or long to rely on soft shells but most are not.

    • Sam Shaheen February 15, 2016 Reply

      Hey Greg, thanks for the kind words!

      I definitely agree with your take on softshells. My go-to kit is all softshell. In 90% of the conditions I face, hardshells are overkill. We are keeping our eye on some companies making super light emergency hardshells (some that are under 5oz) that look interesting — throw them in your pack as a precaution and wear your softshell. Kind of a cool concept!

  21. Victor February 18, 2016 Reply

    Great article. I have been wearing an Arcteryx hard shell with a base layer and an atom jacket for skiing. Comfort wise, I’m plenty warm and never feel sweaty. The problem I’ve noticed, however, is that the hard shell is trapping moisture inside. I had been keeping my phone in the breast shell pocket and after a few runs, I noticed my phone was wet. Considering it was about 25 degrees at Deer Valley, I knew the moisture was coming from me. The base and middle layer were functioning as designed but the Gore Tex shell was trapping the moisture in. I guess I could have opened the pit vents but I never felt warm enough to want to open the vents.

    I think switching to a soft shell product is going to make more sense.

Leave a reply

Your email address will not be published. Required fields are marked *

*